Wednesday, May 6, 2020

Production and Operations Analysis †Free Samples to Students

Question: Discuss about the Production and Operations Analysis. Answer: Introduction The project management is the process of initiating, planning and executing a particular project for the purpose of accomplishing the specified goal (Cleland and Ireland, 2006). It can be related to any particular problem of the corporate world which is resolved with the help of structured procedure (Turner, 2008). The present essay is the case study of Latino Engineering company that has issues related to poor designing and development of equipment, non-responsive customer service team and wrong packaging etc. Owing to this, project management techniques are being applied to resolve the issue and increase customer satisfaction of the business. This assists corporation to create the goodwill in the marketplace and meet the expectations of all related stakeholders. For this purpose, effective tools like Total Quality Management, Six Sigma are applied. Along with that, techniques such as critical path method and Gantt chart an in order to complete different project activities in the ri ght manner. According to the case study, Latino Engineering is unable to meet the expectations of customers as they are not happy with the quality of services delivered and the packaging of the product. The company was sold by Dominic Latino who is the founder of the same and during his time reputation of the firm was good and customers were highly satisfied. tends the employees were retained at the time of purchasing the business, still, management faced complaints in term of; defecting engineering equipment, poor development and design of the product and non-responsiveness of the customers along with the ineffective packaging as well as delivery of the products and services. a , necessary action must be taken by the management so as to address the issue effectively and provide the necessary remedy for the business. It would be effective to cater the requirement of customers and build the image of the business in the marketplace. However, the overall scenario reflects that the issue is with the management only. This is because the company was well-performed at the time of Dominic Latino who was handling each and every activity in the right manner. Therefore, the root cause is related to the management. For this purpose, two techniques such as Total Quality Management (TQM) and Six Sigma are applied for reaching to the root cause of the issue (Kerzner, 2013). Six Sigma technique consists of two methods; DMADV and DMAIC for addressing the issue along with the implementation of the suitable strategy (Burke, 2013; Kwak and Anbari, 2006). According to the case study, Latino Engineering is facing issue related to product quality and development, owing to this, DMADV methodology can be applied. This methodology targets to improve the existing product development phase by proposing the new approach for the development (Snee, 2004). It would be effective to initiate newness in the company so as to grab the attention of customers by offering them new product as per their requirement (Meredith and Mantel Jr, 2011). On the other hand, DMAIC is the data-driven quality strategy which aids to improve the existing procedure for the purpose of maintaining good quality (Winter and et. al., 2006). This indicates that application of DMAIC approach is more suitable for Latino Engineering. The first step of the selected methodology is defining wherein customers are defined in the context of their quality issues and core business involved (Stevenson and Hojati, 2007). As per the current situation of the business, it has that customers require the quick response for the service quality, packaging and delivery aspect of the engineering equipment produced in the firm. Also, they want easy delivery and other effective procedure which facilitates to meet their requirement zero-defect. In this context, business will ensure that requirement of the customers is met effectively by offering the right kind of product and services on the given time span (De Mast and Lokkerbol, 2012). The second step of the selected methodology is the measurement in which data will be collected from the management/ customers of Latino Engineering. For example, information will be collected from the customers that what exactly is not going in the business. For example, the survey will be conducted regarding the quality, delivery and other related aspects of the engineering product with the purpose or goal of maintaining the good quality, increased customer satisfaction and retaining them for longer time span by providing them quick response (Antony and et. al., 2012). With the collected data, it has been found that there exists the gap between the expectation and actual performance of the business. Owing to this, appropriate action must be taken to improve the current situation. At this juncture, derived results will be compared with the actual situation of the business. It is helpful to bring out the suitable solution so as to determine the smooth flow of information and ensure th e betterment of the business for longer time span. In addition to this, analysis of the entire situation proves to be effective in identifying the root cause of the entire situation. The variation was identified that Latino Engineering is not able to meet the expectations of customers because the employees are not motivated. However, it is the fact that if employees are motivated then they tend to deliver good quality of services and ensure to accomplish the aims and objectives of the business (Frings and Grant, 2005). At this juncture, the major issue was related to the low level of motivation among employees. In this regard, a situation will be improved with the creation of an innovative solution that workforce will be provided monetary reward for their better performance. It will be assessed on the basis of monthly evaluation of their performance. However, the reward will be based on their contribution to increasing the customer satisfaction and providing quick response to them. Yet, the problem was related to production and packaging department so the quality department will be set that will provide the standard for the respective issues. At last, control will be done in accord with the continuous monitoring of the internal situation of the business. Total Quality Management (TQM) is another approach which is based on the customer-focused, total employee involvement and process-centred. Along with that, integrated system, continual improvement and fact-based decision-making are included which facilitates in bringing desired improvement (Kaynak, 2003). As per the situation of the Latino Engineering, employees are involved in the decision-making process who can provide their valuable suggestions to improve the service quality. On the other hand, a manufactured product will be based on the expectation of the customers. Also, the packaging department is monitored as per the set standard guidelines (Palo and Padhi, 2003). However, the continuous improvement will be brought through the training of employees in accordance with the issues which are being faced in the organization. (Sadikoglu and Zehir, 2010) With the application of Six Sigma and TQM approach, it has been found that major issue is related to the quality of product and services (Andersson, Eriksson and Torstensson, 2006). Furthermore, the crucial issue was related to lack of motivation among employees and poor supervision of the packing and production department. Owing to this, appropriate plan related to continuous improvement has been implemented in which root cause of the problem will be reduced to a great extent. At the same time, resources requirement will be assessed whereby corporation can effectively create its competitive edge in the marketplace through retention of personnel for longer time span. The plan has been proposed that first of all current situation of the Latino Engineering will be assessed and accordingly causes are identified. It has been found that employees should be provided training and continuous monitoring should be done for the quality department in the context of packing and manufacturing (Isa ksson, 2006). It is estimated that both of the mentioned activities require 12 days and it will be started at the end of the September month and end up in the first week of the October month. The overall analysis derived varied objective of the project plan; improving the service quality, customer satisfaction, zero defect products and higher quality of products and services. For this purpose, strategies such as continuous training, setting separate quality department which looks over the packing and manufacturing department as well as customer issue (Nahmias and Cheng, 2009). All the activities of this particular department will be reported to the head or management at the end of each working day. It will help management to assess the performance of the business. The strategy related to training, the quality department set up will be done as per the allotted time. At this juncture, monitoring will be done on the right time so the obstacles can be overcome. The project team will communicate the improvement efforts by conducting the weekly or daily meeting so that each one can get to know about the structured process associated with the plan. Apart from this, 5whys (refer appendix figure 3) will also be applied to understand the issues which are taking place in the company. For this purpose, first of management asses the abnormal conditions are prevailing in the company as the quality is declining. It is followed by the reason that management issues took place. In this regard, appropriate action should be taken to improve the quality. For example, necessary training and development activities of the employees and setting the quality culture in the business (Velaction Continous improvement, 2016). The project manager set the deadline for all task and employees according to their proficiency and in the same manner, monitoring will be done (Borkar, 2005). The issues identified during the monitoring process will be taken into account to modify the project. Lastly, management of the Latino Engineering will bear in mind regarding the exact practices to be followed to the lifetime of the organization. At this juncture, customers' survey will be conducted and continuous development of employees will be ensured. This facilitates to manufacture the zero-defect product and enable employees to work with integration. A project cannot be completed without employing necessary resources. The major resources are human resources, physical and financial that aid to complete all the project activities in an effectual manner. The financial resources are needed in conducting the training and setting the quality department. On the other hand, physical resources such as laptop, stationary and training hall are required which will be provided by either Latino Engineering or project management team (Kolisch and Hartmann, 2006). These physical resources play the crucial role as all the strategies are implemented by using these resources only. In addition to this, human resources such as entire project team, executive staff of Latino Engineering and its employees are crucial in accomplishing the targets in the right manner. Therefore, it is important for the business to employ all these resources for implementing the project plan and meeting the organizational requirement in the right manner. At the same time, continuous improvement will be brought into the plan whereby it will be possible for the business to retain the customers for longer time span. Further, extra resources will be employed to meet the contingency situation of the business. Developing a continuous improvement plan to ensure the problems and issues are not repeated According to the current study and aforementioned analysis, Latino Engineering will go through the continuous improvement plan. The activity table and Gantt chart of the plan are presented in the appendix which reflects that 51 days are needed for the completion of the project activities. The Gantt chart is prepared through which project manager can easily assign the task as per the deadline and resources can also be arranged in the same manner. The initiation of a project has been done at the end of the September month that will be last until December of the financial year 2017. In this manner, the overall situation of the business has been assessed that why the issue and occurring and what remedies can be provided for the effective solution of the same (Meyringer and Sap Aktiengesellschaft, 2006). The first two activities end up with the collection of data that management related issues should be resolved as it is the root cause of the problem and it will be followed by the stateme nt of the objectives. The standard objective of the project is reduced the customer dissatisfaction to a great level and meet their expectations by manufacturing zero defect product. In this regard, total 4 days were decided to set time frame for the bringing the suitable solution of the problem which is being occurred in the business. Furthermore, total 20 days are consumed in setting the strategies and implementing the same for addressing the issue. For example, training sessions were conducted with the manufacturing and packaging department along with the communication of the standard practices (Kumar, 2005). They were informed that quality department will pass on the guidelines and they have to abide by the same. It is not possible that all plans are completed in the successful manner as certain obstacles are faced in the management of the project. In this regard, project manager applied strategies to integrate personnel and provide them monetary and non-monetary rewards. This will help business in providing the right solution for the corporation and integrating all necessary resources so as to reach to the optimal solution (Fortune and White, 2006). However, communication is considered as the strongest tool for the successful completion of any project. For this purpose, daily or weekly meeting have been conducted to assess the progress of the project and let the employee know the potential issues. Therefore, varied activities are communicated to the management. The critical path method technique has been applied in the project so as to reduce the time taken in the project and cost involved in the same. The critical path method displayed in the appendix shows that major activities covered in the project are 1+2+3+4+5+7+9+11+12+13=31 days. It reflects that duration of the project is reduced by 20 days with the application of this method. It aids to complete the project in relatively less because two or more than two activities are completed simultaneously (Achanga and et. al., 2006). However, application of such kind of activities might require additional resources but time will be reduced to a great extent. This facilitates to improve the performance of the business on the right time. Therefore, critical path method helps project management team to accomplish the project before the same time and provide the overall benefit for the organization to create its competitive edge in the marketplace. Conclusion The aforementioned report concludes that application of suitable software tend to reduce the time taken in the completion of the project. For this purpose, critical path method and Gantt chart are effective which support management in completing the business activities in the right manner and deliver good quality of services to client. The continuous improvement plan of the Latino Engineering generates huge cost but the overall quality of services will be improved as each and every aspect is supervised under the plan of continuous development. Here, the important part of continuous development is employees involved n the product and service department of the business. However, it is important for management of Latino Engineering to conduct the audit skills of employees and assess the training need among employees. This will helpful for the workforce to understand the standards set by the business and works upon the same to derive the quality outcome. Furthermore, employees should be reward who achieves the quality standard. This will assist business to implement the continuous development plan in the organization. References Achanga, P., Shehab, E., Roy, R. and Nelder, G., 2006. Critical success factors for lean implementation within SMEs.Journal of Manufacturing Technology Management,17(4), pp.460-471. Andersson, R., Eriksson, H. and Torstensson, H., 2006. Similarities and differences between TQM, six sigma and lean.The TQM magazine,18(3), pp.282-296. Antony, J., Singh Bhuller, A., Kumar, M., Mendibil, K. and Montgomery, D.C., 2012. Application of Six Sigma DMAIC methodology in a transactional environment.International Journal of Quality Reliability Management,29(1), pp.31-53. Borkar, S., 2005. Designing reliable systems from unreliable components: the challenges of transistor variability and degradation.Ieee Micro,25(6), pp.10-16. Burke, R., 2013. Project management: planning and control techniques.New Jersey, USA. Cleland, D.L. and Ireland, L.R., 2006.Project management. McGraw-Hill Professional. De Mast, J. and Lokkerbol, J., 2012. An analysis of the Six Sigma DMAIC method from the perspective of problem solving.International Journal of Production Economics,139(2), pp.604-614. Fortune, J. and White, D., 2006. Framing of project critical success factors by a systems model.International Journal of Project Management,24(1), pp.53-65. Frings, G.W. and Grant, L., 2005. Who moved my Sigma effective implementation of the Six Sigma methodology to hospitals.Quality and Reliability Engineering International,21(3), pp.311-328. Isaksson, R., 2006. Total quality management for sustainable development: Process based system models.Business Process Management Journal,12(5), pp.632-645. Kaynak, H., 2003. The relationship between total quality management practices and their effects on firm performance.Journal of operations management,21(4), pp.405-435. Kerzner, H., 2013.Project management: a systems approach to planning, scheduling, and controlling. John Wiley Sons. Kolisch, R. and Hartmann, S., 2006. Experimental investigation of heuristics for resource-constrained project scheduling: An update.European journal of operational research,174(1), pp.23-37. Kumar, P.P., 2005. Effective use of Gantt chart for managing large scale projects.Cost engineering,47(7), pp.14-21. Kwak, Y.H. and Anbari, F.T., 2006. Benefits, obstacles, and future of six sigma approach.Technovation,26(5), pp.708-715. Meredith, J.R. and Mantel Jr, S.J., 2011.Project management: a managerial approach. John Wiley Sons. Meyringer, M. and Sap Aktiengesellschaft, 2006.Interactive and web-based Gantt Chart. U.S. Patent 7,050,056. Nahmias, S. and Cheng, Y., 2009.Production and operations analysis(Vol. 4). New York: McGraw-Hill/Irwin. Palo, S. and Padhi, N., 2003. Measuring effectiveness of TQM training: an Indian study.International Journal of Training and Development,7(3), pp.203-216. Sadikoglu, E. and Zehir, C., 2010. Investigating the effects of innovation and employee performance on the relationship between total quality management practices and firm performance: An empirical study of Turkish firms.International journal of production economics,127(1), pp.13-26. Snee, R.D., 2004. SixSigma: the evolution of 100 years of business improvement methodology.International Journal of Six Sigma and Competitive Advantage,1(1), pp.4-20. Stevenson, W.J. and Hojati, M., 2007.Operations management(Vol. 8). Boston: McGraw-Hill/Irwin. Turner, J.R., 2008.Handbook of project-based management. McGraw-Hill Professional Publishing. Winter, M., Smith, C., Morris, P. and Cicmil, S., 2006. Directions for future research in project management: The main findings of a UK government-funded research network.International journal of project management,24(8), pp.638-649.

No comments:

Post a Comment

Note: Only a member of this blog may post a comment.